Set Up An Appointment

We have uncovered this article on How to Install a Bathtub Yourself directly below on the web and felt it made perfect sense to discuss it with you on this page.

Mounting a bathtub isn't exactly rocket science, but it does need strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is conveniently available, the task can move easily; if you need to open up a wall surface to get rid of the old tub and place the new bath tub, the job is much harder. In either instance, the task is within a residence handyman's skills, although you will need an assistant to vacate the old tub and set in the brand-new one. Make sure you have certified on your own for the task as well as fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly aid you mount a brand-new bathtub in your restroom if you have already acquired a new bathtub as well as don't need to change the setup of your previous supply of water pipes.
Your devices and also product checklist should make up the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Setup

First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather problematic due to the limited gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

Installing the Bathtub

Using the two wooden boards under its feet, place the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub till the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and also check all joints as well as brand-new pipework for leakages and tighten them if essential. Fill the tub as well as additionally examine the overflow outlet and also the typical outlet for leakages.
Finally, repair the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has actually been used a minimum of once as this will certainly resolve it right into its last placement.

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the area where the bath fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, resulting in difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof adhesive and grout.

Bathtub Installation

How Important Is A Bathtub To Your Home?

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

Install Piping Before Tub

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

Position the Tub

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

Assemble Drain Connections

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

Place a Pipe For the Shower Head

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

Attaching Hot and Cold Water Lines

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

Install the Spout

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

Check For Leaks

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

estore the Bathroom Wall

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

I hope you enjoyed reading our topic on How to Install a Bathtub Yourself. Thanks a ton for spending some time to read through our post. Loved our blog? Please share it. Let another person locate it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Leading plumbing expertise for emergencies.